The Coop Almanac

Incubator Temperature and Humidity for Chicken Eggs

Incubator temperature and humidity for chicken eggs, with extension and maker figures side by side: forced-air vs still-air, days 1–18, and lockdown.

At a glance
  • Forced-air (fan): 100°F per Mississippi State; makers' presets 99.5°F. Maryland gives 99.5°F, type not named.
  • Still-air: 102°F at the top of the eggs (Mississippi State) or 100.5°F (Illinois Extension).
  • Humidity: about 40–60% until 3 days before hatch, then 65% or more for hatching, depending on the source.
In this guide
  1. Temperature
  2. Humidity, days 1–18
  3. Humidity at hatch (lockdown)
  4. How to adjust humidity
  5. Before you set eggs
  6. Bottom line

For chicken eggs in a forced-air (fan) incubator, Mississippi State University Extension recommends 100°F for the whole incubation; the Brinsea and Nurture Right factory presets use 99.5°F. University of Maryland Extension also gives 99.5°F, without naming an incubator type. A still-air incubator runs warmer: 102°F at the top of the eggs per Mississippi State, or 100.5°F per Illinois Extension. Sources put relative humidity between about 40% and 60% until three days before hatch, then 65% or more for the hatch.

The exact figures differ by source, so they are shown side by side below. We don’t average them. Your incubator’s manual comes first.

Temperature

SourceForced-air (fan)Still-air (no fan)Where to measure / notes
Mississippi State University Extension100°F “throughout the entire incubation period”102°FThermometer bulb at the height of the top of the eggs; less than ½ degree swings are tolerated, no more than 1 degree in total
University of Maryland Extension99.5°F (Table 1, chickens; incubator type not specified)not given separatelyPlace a second thermometer at egg level
University of Illinois Extensionnot covered100.5°F optimum; 99–103°F rangeNever keep at 103°F for more than a few hours; thermometer on the wire grate, away from the heat source, in the center
Brinsea (Mini II Advance)factory preset 99.5°F (37.5°C), “fully adjustable”—Maker’s setting
Nurture Right 360 (Manna Pro)factory preset 99.5°F; its chart keeps 99.5°F through lockdown—Maker’s setting
UC Davis & UC Cooperative Extension (2015 article)99–100°F days 1–17; 97–99°F days 18–21 (type not specified)—Says 99.5°F “is where most people have the best results”

Why still-air is set higher. Mississippi State says the higher figure is “to compensate for the temperature layering within the incubator,” and that temperature is measured “at the level where the embryos develop (at the top of the egg),” so where you put the thermometer matters.

Too hot or too cold. Maryland Extension says temperatures that are too hot may cause an early hatch or dead chicks or embryos; too cold may cause late hatches and more embryo deaths. Illinois Extension says too low an average temperature will delay the hatch.

The room matters too. Maryland Extension advises keeping incubators out of direct sunlight, ideally in an inside room with little temperature change. The Nurture Right 360 manual asks for a room between 74–80°F that doesn’t drop below 72°F at night, away from windows and drafts, and not on the floor.

Humidity, days 1–18

“Humidity” here is relative humidity (RH), read on a hygrometer. Mississippi State notes that the industry often states it as a wet-bulb temperature instead, and the two convert with a psychrometric table; where a source gives both, both are listed.

SourceSetting until 3 days before hatchNotes
Mississippi State University Extension58–60% RH (84–86°F wet bulb)“between setting and 3 days prior to hatching”; the species table on the same page lists 85–87°F wet bulb (and 90°F wet bulb for the last 3 days)
University of Maryland Extension55–60%Check water levels daily; drier rooms need more water
University of Illinois Extension50–55% RH (about 85–87°F wet bulb)Keeping the water level right in the bottom should hold the humidity
Nurture Right 360 (Manna Pro)around 50% (48–55% acceptable)One water pot, vent half open
UC Davis & UC Cooperative Extension (2015 article)40–60% (days 1–17)Gives days 1–17 rather than “until 3 days before hatch”

Humidity at hatch (lockdown)

SourceAt hatchWhen to raise it
Mississippi State University Extension65% RH or more“When hatching”
University of Maryland Extension70%When you see the first small pip hole
University of Illinois Extensionno % givenAdd humidity on Day 18 with 2–3 wet sponges in the bottom
Nurture Right 360 (Manna Pro)around 70% (65–75% acceptable)The last 3 days: fill both water pots, open the vent fully
UC Davis & UC Cooperative Extension (2015 article)70–80%Days 18–21

The site’s hatch calendar and day-by-day strip use day 18 for lockdown, when turning stops. Timeline details are in how long chicken eggs take to hatch.

How to adjust humidity

Five of the seven incubators in our comparison rely on water you add; you control humidity with the water and the vents.

  • Add water to raise it. Maryland Extension says incubators have built-in reservoirs that must hold water throughout incubation. Nurture Right says to check its water pots every 24 hours and refill as needed, and recommends warm distilled water (80–90°F) to avoid chilling the eggs.
  • Close the vent a little to raise it, open to lower it. Nurture Right says this, but its vent must stay at least 1/3 open for the first 18 days and fully open for the last 3, for air.
  • Wait before changing again. Nurture Right says to allow 2–3 hours for humidity to stabilize after adding water or moving the vent.
  • Watch for too much. Illinois Extension says lots of condensation on the inside of the windows probably means too much moisture, though it adds this is usually not a big problem, and that chicks come out “wet and mushy” if humidity is too high.

Some incubators control humidity automatically. Brinsea lists an integral humidity pump on the Maxi 24 EX, and VEVOR says its 48H draws water from a bottle; see the egg incubator comparison.

Before you set eggs

  • Run the incubator at least 24 hours before setting eggs, so it reaches temperature and you can fix problems (Maryland Extension). Nurture Right asks for at least 5 hours with warm water in the pot.
  • Use a second thermometer at egg level (Maryland Extension); Nurture Right recommends a secondary glass thermometer inside the incubator to check its display.
  • Keep the lid closed during lockdown. Nurture Right says each opening makes humidity “fall dramatically,” and not to open the lid more often than every 6 hours unless absolutely necessary.

Bottom line

Set a fan incubator to 100°F (Mississippi State) or the maker’s preset (99.5°F for Brinsea and Nurture Right); Maryland Extension’s general figure is also 99.5°F. Set a still-air incubator to 102°F at egg-top height (Mississippi State) or 100.5°F (Illinois). Hold humidity in your chosen source’s range (40–60% across the five) until day 18, then raise it to 65% or more (Mississippi State) or around 70% (Maryland Extension, Nurture Right), or 70–80% (UC Davis/UC Cooperative Extension) for the hatch. Check readings with a second thermometer, and give humidity 2–3 hours to settle after each change, as Nurture Right advises.

Sources (9)
  1. Mississippi State University Extension — Important incubation factors (checked 2026-11-11)
  2. University of Maryland Extension — Hatching Eggs at Home, FS-1114, April 2020, pp. 1–4 (checked 2026-11-11)
  3. University of Illinois Extension — Incubation and Embryology Q&A (checked 2026-11-11)
  4. Nurture Right 360 instructions (Manna Pro), PDF pp. 1–2 (checked 2026-11-11)
  5. Nurture Right 360 FAQ (Manna Pro), PDF p. 6, incubation chart (checked 2026-11-11)
  6. Brinsea — Mini II Advance 7-egg incubator (checked 2026-11-11)
  7. Brinsea — Maxi 24 EX fully automatic 24-egg incubator (checked 2026-11-12)
  8. VEVOR — 48 Egg Incubator (checked 2026-11-12)
  9. UC Davis School of Veterinary Medicine & UC Cooperative Extension — The Science of Incubation, 2015, pp. 3–4 (checked 2026-11-12)

More on incubation

All →